Classic British SparesKlempf British PartsBaxter CycleBritBike Sponsor SteadfastCyclesSRM EngineeringLucas Classic MotorcycleHepolite PistonsIndustrial tec supply

Upgrade your membership to: Premium Membership | Gold Membership | Life Membership | Vendor Membership | Site Sponsor Membership
Welcome to BritBike Forum!
Britbike forum logo
Member Spotlight
Posts: 104
Joined: August 2001
Comment Guidelines: Do post respectful and insightful comments. Don't flame, hate, spam.
Search eBay for motorcycle parts in following countries
Australia, Canada, France, Holland, Italy, United Kingdom, USA
Thread Like Summary
Allan G, Psychopasta, TR6Ray
Total Likes: 3
Original Post (Thread Starter)
by Mark Z
Mark Z
This is primarily in response to TR6Ray's query in the "tank rubbers" thread, but I think it may be of help to others who may have to deal with a 1967 fuel tank, so I started a new thread. The 1967 fuel tank is unique, and as I learned the hard way, improper mounting can lead to the breaking of bits which are getting harder and harder to source as time goes on.

The first photo shows the distance from the fuel tank to the handlebar mounting bolt. I know you can't read the ruler in the photo, but the distance is 9/16".
[Linked Image from]
The next photo shows the height of the fuel tank relative to the frame, and the location of the lower bracket. Ray asked, how does the rubber bushing stay in place? The answer is, it fits into the bracket very tightly. For many of the rubber bits, I've found it's better to make your own; then you can determine the needed dimensions and the consistency of the material used. This bushing must be quite firm, in order to keep the fuel tank from rocking side to side, which can lead to breakage, primarily at the top mount. My bushing happens to have a flange on the end, but this is not necessary. I also added a rubber washer between the bracket and the frame to cushion the bracket a bit.
[Linked Image from]
Since I was taking pictures, I thought I'd also address the center mount assembly. The rubber bushing, which gets inserted into the chrome cup, and the flat washer, slip over the sleeve shown in the last photo. The shouldered nut however, butts up against the end of the sleeve. This is important because you don't want a lot of downward force against the chrome cup; that will break the cup.
[Linked Image from]
This photo shows the rubber O-ring and trim pieces. On my '67 L, which was original when I bought it, there was also a flat metal ring, or washer, which I believe is also shown in the Spares manual. However, whether above or below the O-ring, assembly with that metal ring simply DOES NOT WORK. It does not allow the ends of the trim pieces to fit into the slots in the chrome cup, and results in breaking off the ends of the trim pieces and/or the chrome cup.
[Linked Image from]
Finally, a picture of the center mount bolt and sleeve, which are correct NOS parts, and the tank rubbers. I like to tape the rubbers in place to facilitate assembly. The front rubber measures 1 1/4" in height, and the rear rubber measures 3/4" in height.
[Linked Image from]
Liked Replies
by KC in S.B.
KC in S.B.
Mark, please educate me. What makes the ‘67 tank unique, aside from the cap? Is the shape different, and causes this Clearance issue? Had 5 A65s and never noticed a shape difference in height, always thought the cap was the only concern. Interesting for sure! I do know my ‘67 tank to bars clearance is SCARY close at turned to stop!
1 member likes this
Job CycleBritish Cycle SupplyMorries PlaceKlempf British PartsPodtronicVintage MagazineBSA Unit SinglesBritBike SponsorBritish Tools & FastenersBritBike SponsorBritBike Sponsor

© 1996-2021
Powered by UBB.threads™ PHP Forum Software 7.7.5